46 CFR Part 162
PART 162—ENGINEERING EQUIPMENT
- PART 162—ENGINEERING EQUIPMENT
- Chapter I—Coast Guard, Department of Homeland Security › Subchapter Q—Equipment, Construction, and Materials: Specifications and Approval
- Subpart 162.017—General Provisions; Valves, Pressure-Vacuum Relief, for Tank Vessels
- § 162.017-0 Preemptive effect.
- § 162.017-1 Incorporation by reference.
- § 162.017-2 Type.
- § 162.017-3 Materials, construction, and workmanship.
- § 162.017-4 Inspections and testing.
- § 162.017-5 Marking.
- § 162.017-6 Procedure for approval.
- Subpart 162.018—Safety Relief Valves, Liquefied Compressed Gas
- § 162.018-1 Applicable specifications, and referenced material.
- § 162.018-2 Scope.
- § 162.018-3 Materials.
- § 162.018-4 Construction and workmanship.
- § 162.018-5 Blow-down adjustment and popping tolerance.
- § 162.018-6 Marking.
- § 162.018-7 Flow rating tests.
- § 162.018-8 Procedure for approval.
- Subpart 162.027—Combination Firehose Nozzles
- § 162.027-1 Scope.
- § 162.027-2 Incorporation by reference.
- § 162.027-3 Design, construction, testing, and marking requirements.
- § 162.027-4 Approval procedures.
- Subpart 162.028—Extinguishers, Fire, Portable, Marine Type
- § 162.028-1 Incorporation by reference.
- § 162.028-2 Classification.
- § 162.028-3 Requirements.
- § 162.028-4 Marine type label.
- § 162.028-5 Recognized laboratories.
- § 162.028-6 Examinations, tests, and inspections.
- § 162.028-7 Procedure for listing and labeling.
- § 162.028-8 Termination of listing or labeling.
- Subpart 162.039—Extinguishers, Fire, Semi-portable, Marine Type
- § 162.039-1 Incorporation by reference.
- § 162.039-2 Classification.
- § 162.039-3 Requirements.
- § 162.039-4 Marine type label.
- § 162.039-5 Recognized laboratories.
- § 162.039-6 Examinations, tests, and inspections.
- § 162.039-7 Procedure for listing and labeling.
- § 162.039-8 Termination of listing or labeling.
- Subpart 162.050—Pollution Prevention Equipment
- § 162.050-1 Scope.
- § 162.050-3 Definitions.
- § 162.050-4 Incorporation by reference: Where can I get a copy of the publications mentioned in this part?
- § 162.050-5 Contents of application.
- § 162.050-7 Approval procedures.
- § 162.050-9 Test report.
- § 162.050-11 Marking.
- § 162.050-13 Factory production and inspection.
- § 162.050-15 Designation of facilities.
- § 162.050-17 Separator test rig.
- § 162.050-19 Oil content meter and bilge alarm test rig.
- § 162.050-20 Separator and bilge alarm test fluids.
- § 162.050-21 Separator: Design specification.
- § 162.050-23 Separator: Approval tests.
- § 162.050-25 Cargo monitor: Design specification.
- § 162.050-27 Oil content meter: Approval tests.
- § 162.050-33 Bilge alarm: Design specification.
- § 162.050-35 Bilge alarm: Approval tests.
- § 162.050-37 Vibration test.
- § 162.050-39 Measurement of oil content.
- Subpart 162.060—Ballast Water Management Systems
- § 162.060-1 Purpose and scope.
- § 162.060-3 Definitions.
- § 162.060-5 Incorporation by reference.
- § 162.060-10 Approval procedures.
- § 162.060-12 Use and acceptance of existing test data.
- § 162.060-14 Information requirements for the ballast water management system (BWMS) application.
- § 162.060-16 Changes to an approved ballast water management system (BWMS).
- § 162.060-18 Suspension, withdrawal, or termination of approval.
- § 162.060-20 Design and construction requirements.
- § 162.060-22 Marking requirements.
- § 162.060-24 Test Plan requirements.
- § 162.060-26 Land-based testing requirements.
- § 162.060-28 Shipboard testing requirements.
- § 162.060-30 Testing requirements for ballast water management system (BWMS) components.
- § 162.060-32 Testing and evaluation requirements for active substances, preparations, and relevant chemicals.
- § 162.060-34 Test Report requirements.
- § 162.060-36 Quality Assurance Project Plan (QAPP) requirements.
- § 162.060-38 Operation, Maintenance, and Safety Manual (OMSM).
- § 162.060-40 Requirements for Independent Laboratories (ILs).
- § 162.060-42 Responsibilities for Independent Laboratories (ILs).
- Subpart 162.161—Fixed Clean Agent Fire Extinguishing Systems
- § 162.161-1 Scope.
- § 162.161-2 Incorporation by reference.
- § 162.161-3 Materials.
- § 162.161-4 Construction.
- § 162.161-5 Instruction manual for design, installation, operation, and maintenance.
- § 162.161-6 Tests for approval.
- § 162.161-7 Inspections at production.
- § 162.161-8 Marking.
- § 162.161-9 Procedure for approval.
- Subpart 162.163—Portable Foam Applicators
- § 162.163-1 Scope.
- § 162.163-2 Incorporation by reference.
- § 162.163-3 Performance, design, construction, testing, and marking requirements.
- § 162.163-4 Approval procedures.
Feedback