Regulation No 11 of the Economic Commission for Europe of the United Nations ... (42010X0513(01))
Regulation No 11 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with regard to door latches and door retention components
- Regulation No 11 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with regard to door latches and door retention components
- 1. SCOPE
- 2. DEFINITIONS
- 3. APPLICATION FOR APPROVAL
- 4. APPROVAL
- 5. GENERAL REQUIREMENTS
- 5.2. Door latches
- 6. PERFORMANCE REQUIREMENTS
- 6.1. Hinged doors
- 6.1.1. Load test one
- 6.1.2. Load test two
- 6.1.3. Load test three (applicable to doors that open in a vertical direction)
- 6.1.4. Inertial load.
- 6.1.5. Door hinges
- 6.2. Sliding side doors
- 6.2.1. Load test one
- 6.2.2. Load test two
- 6.2.3. Inertial load
- 6.2.4. Door system
- 6.3. Door locks
- 6.3.2. Rear side doors
- 6.3.3. Back doors
- 7. TEST PROCEDURES
- 7.1. Hinged doors
- 7.1.1. Door latches
- 7.1.1.1. Load tests one, two, and three, force application
- 7.1.1.2. Inertial force application
- 7.1.2. Door hinges
- 7.2. Sliding side doors
- 7.2.1. Door latches
- 7.2.1.1. Load tests one and two, force application
- 7.2.1.2. Inertial force application
- 7.2.2. Door system
- 8. MODIFICATION AND EXTENSION OF APPROVAL OF THE VEHICLE TYPE
- 9. CONFORMITY OF PRODUCTION
- 10. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 11. PRODUCTION DEFINITELY DISCONTINUED
- 12. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
- 13. TRANSITIONAL PROVISIONS
- ANNEX 1
- COMMUNICATION
- (Maximum format: A4 (210 × 297 mm))
- ANNEX 2
- ARRANGEMENTS OF APPROVAL MARKS
- MODEL A
- (See paragraph 4.4 of this Regulation)
- MODEL B
- (See paragraph 4.5 of this Regulation)
- ANNEX 3
- LATCH TEST FOR LOAD TESTS ONE, TWO, AND THREE, FORCE APPLICATION
- 1. PURPOSE
- 2. TEST OPERATION
- 2.1. Load test one
- 2.1.2. Procedures
- 2.1.2.1. Fully latched position
- 2.1.2.2. Secondary latched position
- 2.2. Load test two
- 2.2.2. Procedures
- 2.2.2.1. Fully latched position
- 2.2.2.2. Secondary latched position
- 2.3. Load test three (for doors that open in a vertical direction)
- 2.3.2. Procedure
- Figure 3-1
- Door latch — Tensile testing fixture for load test one
- Figure 3-2
- Door latch — Tensile testing fixture for load test two
- Figure 3-3
- Door latch — Tensile testing fixture for load test three (for doors that open in a vertical direction)
- Figure 3-4
- Door static load test directions
- ANNEX 4
- INERTIAL TEST PROCEDURES
- 1. PURPOSE
- 2. TEST PROCEDURES
- 2.2. Option 2, Full Vehicle Dynamic Test
- 2.2.1. Test equipment
- 2.2.2. Test setup
- 2.2.3. Test directions (see Figure 4-3)
- 2.3. Option 3, Door Dynamic Test
- 2.3.1. Test equipment
- 2.3.2. Test setup
- 2.3.3. Test directions (see Figure 4-3)
- 2.4. Test operation for Options 2 and 3
- Figure 4-1
- Inertial loading — Sample calculation
- Table 4-1
- Acceleration Pulse Corridor
- Figure 4-2
- Acceleration Pulse
- Figure 4-3
- Vehicle coordinate reference system for inertial testing
- ANNEX 5
- HINGE TEST PROCEDURE
- 1. PURPOSE
- 2. TEST PROCEDURE
- 2.1. Multiple Hinge System
- 2.1.1. Longitudinal load test
- 2.1.1.1. Equipment
- 2.1.1.2. Procedure
- 2.1.2. Transverse load test
- 2.1.2.1. Equipment
- 2.1.2.2. Procedure
- 2.1.3. Vertical load test (for doors that open in the vertical direction)
- 2.1.3.1. Equipment
- 2.1.3.2. Procedure
- 2.2.1. Test procedures
- Figure 5-1
- Static test fixtures
- Figure 5-2
- Static load test directions for doors that open in the vertical direction
- ANNEX 6
- SLIDING SIDE DOOR
- Full door test
- 1. PURPOSE
- 2. GENERAL PROVISIONS
- 3. TEST SETUP
- 4. TEST PROCEDURE
- Figure 6-1
- Sliding side door full vehicle test procedure (note: sliding door is shown separated from the vehicle)
Feedback